# CrawlWorx

> RC crawling hub: every printable upgrade for your rig, sorted by chassis, with a fit status on every part and the gearing math built in. A directory of 3D-printable parts for the Axial SCX10 III, Traxxas TRX-4, Axial SCX24 and Traxxas TRX-4M, plus a gearing calculator.

Each part links to its original listing and credits the designer. No part has been test-fitted by CrawlWorx yet. Fit status is either reported (the designer or reviewers say it fits; not confirmed by us) or unverified (nobody has confirmed the fit). Material and hardware are listed only when the source states them.

## Pages
- [Gearing calculator](https://crawlworx.com/gearing/): crawl ratio, TRX-4 front/rear overdrive, and wheel speed from KV, voltage and tire diameter. Stock values are cited; estimated values are labelled.
- [Shop](https://crawlworx.com/shop/): CrawlWorx original parts (coming soon)
- [About the data](https://crawlworx.com/about/)

## Axial SCX10 III (14 parts): https://crawlworx.com/chassis/scx10-iii/

- [SCX10 III Battery Box](https://www.thingiverse.com/thing:6527721): Battery trays; by bwinkl04 on Thingiverse; fit: unverified
- [SCX10 III Cantilever Suspension](https://cults3d.com/en/3d-model/gadget/scx10-iii-cantilever-suspension): Suspension; by hotrodtrevor on Cults3D; fit: reported; material: 100% infill (material not stated); hardware: Spare screws plus 1 turnbuckle
- [Hinged Body Mount (Early Bronco)](https://www.printables.com/model/411571-hinged-body-mount-for-axial-scx10iii-early-bronco): Body mounts; by Zanthrax on Printables; fit: reported; hardware: Stock screws; 50 mm M3 threaded rod (or 2x 25 mm screws) as hinge pin
- [SCX10.3 Comp Sliders](https://makerworld.com/en/models/2376951-axial-scx10-3-comp-sliders): Sliders; by hodgecattleco on MakerWorld; fit: unverified; material: PLA (print profile)
- [SCX10 III Drive Shaft Improvement](https://www.printables.com/model/1022605-axial-scx-10-iii-drive-shaft-improvement-antriebsw): Drivetrain; by DustinTRC on Printables; fit: unverified; material: PCTG, PETG, Nylon or ASA
- [SCX10 III DIG Lever (1:1 replacement)](https://www.printables.com/model/1517147-axial-scx10-iii-dig-hebel): Drivetrain; by Charly_Brown on Printables; fit: unverified; material: PA6-CF (designer); PETG suggested; hardware: 4x15 mm dowel pin
- [SCX10 III Clipless Body Mount (JLU)](https://cults3d.com/en/3d-model/various/scx10iii-clipless-bodymount): Body mounts; by NorfDesigns on Cults3D; fit: unverified; material: PLA+ or PETG; hardware: Screws 3-5 mm longer than stock
- [SCX10 III ESC Mount (Mamba X)](https://www.printables.com/model/304198-scx10-iii-esc-mount-mamba-x): Electronics mounts; by Heliguy71 on Printables; fit: unverified; material: PETG; hardware: 2x M3x6 mm screws; uses stock holes
- [SCX10 III Front Shock Towers (Base Camp)](https://makerworld.com/en/models/1131213-axial-scx10-iii-front-shock-towers-base-camp): Suspension; by SB Artisan Creations on MakerWorld; fit: reported; material: PETG (tested); ABS-GF or PETG-CF suggested
- [SCX10 III Front ESC Mount Plate](https://makerworld.com/en/models/1832347-scx10-iii-front-esc-mount-plate): Electronics mounts; by irlbabayaga on MakerWorld; fit: unverified; material: ABS (print profile); hardware: Countersunk M3 screws
- [SCX10 III Gladiator Rails](https://makerworld.com/en/models/669607-scx10-iii-gladiator-rails): Scale accessories; by K&S Outdoors on MakerWorld; fit: unverified; material: PLA (print profile)
- [SCX10 III High Clearance Bumper](https://www.printables.com/model/912839-scx10-iii-high-clearance-bumper): Bumpers; by Jimjo on Printables; fit: unverified; material: Nylon, ABS or PETG; hardware: Heat-set version: 4x M3x4x5 mm inserts; reuses stock bumper screws
- [SCX10 III Slick Slider](https://www.printables.com/model/1314232-scx10iii-slick-slider): Sliders; by Jimjo on Printables; fit: unverified; material: Nylon, ABS or PETG; hardware: 4x M3 countersunk screws, 8-10 mm
- [SCX10 III Gladiator Flatbed](https://cults3d.com/en/3d-model/game/scx10-iii-gladiator-flatbed): Bodies & beds; by ahead_RC on Cults3D; fit: reported; material: PLA+; hardware: M3 countersunk 20 mm (5), 15 mm (4), 10 mm (7); M3 socket 10 mm (6) and 15-20 mm (4); 4 M3 nylocks; 4 M3 washers

## Traxxas TRX-4 (15 parts): https://crawlworx.com/chassis/trx-4/

- [Low CG Battery Tray (easy to print)](https://www.printables.com/model/265630-low-cg-battery-tray-for-trx-4-easy-to-print): Battery trays; by CippyO on Printables; fit: unverified; hardware: 2x M3x10 countersunk screws to join the halves
- [TRX-4 Bumper Mount Delete](https://cults3d.com/en/3d-model/game/traxxas-trx-4-bumper-mount-delete): Bumpers; by CommaLlama on Cults3D; fit: unverified; material: TPU 95A (designer)
- [TRX-4 Front Battery Mount](https://www.printables.com/model/127670-trx-4-front-battery-mount): Battery trays; by Dao20 on Printables; fit: unverified; hardware: 4 screws and a velcro strap
- [TRX-4 Front Mounted Battery Tray](https://www.printables.com/model/203737-traxxas-trx-4-front-mounted-battery-tray): Battery trays; by Outlaw_NL on Printables; fit: unverified; material: PLA (ABS/PETG should work)
- [TRX-4 Low CG Battery Tray for Large Batteries](https://www.thingiverse.com/thing:4244385): Battery trays; by MexGessi on Thingiverse; fit: unverified
- [TRX-4 Roof Rack Crossbar](https://makerworld.com/en/models/1660566-trx-4-roof-rack-crossbar): Scale accessories; by Filipes91 on MakerWorld; fit: unverified; hardware: M2x12 screws, M2 nuts
- [TRX4 Chain/Track Drive (All-Terrain Traxx)](https://www.printables.com/model/768524-traxxas-trx4-chain-drive-track-drive-all-terrain-t): Drivetrain; by Mr.(Pr)interesting on Printables; fit: reported; material: TPU (chain); PLA or PETG (rest); hardware: Bearings: 4x 27x20x4, 4x 15x21x4, 40x 19x6x6; M3 screws
- [TRX4 Defender Top Plate](https://makerworld.com/en/models/1815148-traxxas-trx4-defender-top-plate): Scale accessories; by Dutchrogeu on MakerWorld; fit: unverified
- [TRX4 Diff Lock Servo Lay-Down Mount](https://makerworld.com/en/models/1870606-trx4-diff-lock-servo-lay-down-mount): Electronics mounts; by mapache on MakerWorld; fit: unverified
- [TRX4 Front Axle Shock Link Mount](https://www.printables.com/model/806335-traxxas-trx4-front-axle-shock-link-mount): Suspension; by itsw on Printables; fit: reported; material: Nylon 6-CF (PLA too brittle, PETG too weak per designer)
- [TRX-4 Servo Mount 5 mm Down](https://www.printables.com/model/1082037-trx-4-servo-mount-5mm-down): Suspension; by D-Tecc on Printables; fit: unverified; material: PLA (print profile)
- [TRX4 Front Bumper Mount](https://cults3d.com/en/3d-model/various/trx4-front-bumper-mount): Bumpers; by kiatkla on Cults3D; fit: unverified
- [TRX4 Low CG Battery Tray with Receiver/ESC Mount](https://www.thingiverse.com/thing:5417713): Battery trays; by matador on Thingiverse; fit: unverified
- [TRX4 Sliders with Magnetic Body Mounts (Pinched Toyota)](https://www.printables.com/model/1186771-traxxas-trx4-sliders-with-bodymount-and-parts-for): Sliders; by JohnE on Printables; fit: unverified; hardware: Reuses the stock slider screws; magnets glued to body and posts
- [TRX4 & TRX6 Chassis Parts](https://www.printables.com/model/1365551-traxxas-trx4-6-chassis-parts): Chassis; by Revellio on Printables; fit: unverified; material: PLA (designer, 15% infill); hardware: M3 screws; some parts take pressed-in M3 nuts

## Axial SCX24 (15 parts): https://crawlworx.com/chassis/scx24/

- [SCX24 Axle Skid Plate](https://www.printables.com/model/161662-scx24-axle-skid-plate): Skids & protection; by Chris on Printables; fit: unverified; material: PETG (designer)
- [High Clearance SCX24 Chassis](https://makerworld.com/en/models/1390060-high-clearance-scx24-chassis): Chassis; by Craig on MakerWorld; fit: reported
- [SCX24 C-Bolt High Clearance Links](https://cults3d.com/en/3d-model/gadget/scx24-c-bolt-high-clearance-links): Links; by TnkCmmndr on Cults3D; fit: unverified; material: PLA (designer); hardware: Ball ends
- [SCX24 Buggy Chassis](https://www.printables.com/model/1156782-scx24-buggy): Chassis; by 1_24Buddy on Printables; fit: unverified; material: PETG (0.25 mm nozzle); hardware: Mostly M1.4 hardware; body panels super-glued
- [Bumper for Axial SCX24](https://cults3d.com/en/3d-model/game/bumper-for-axial-scx24): Bumpers; by JayWorks on Cults3D; fit: unverified; material: PLA or PETG (tested)
- [LCG SCX24 Chassis](https://www.printables.com/model/1148918-lcg-scx24-chassis): Chassis; by DerakCZ on Printables; fit: reported
- [SCX24 Flex Link Mod](https://www.printables.com/model/1160264-scx24-flex-link-mod): Suspension; by Josh on Printables; fit: unverified; hardware: Relocates the stock shocks lower
- [SCX24 Front Lower Links 40/42/44](https://makerworld.com/en/models/2651379-scx24-front-lower-links-40-42-44): Links; by Sal C. on MakerWorld; fit: unverified; material: PETG (print profile)
- [SCX24 Gladiator Rock Sliders](https://www.printables.com/model/137046-scx24-gladiator-rock-sliders): Sliders; by N3EIL on Printables; fit: unverified
- [SCX24 Hardbody](https://www.printables.com/model/1184151-scx24-hardbody): Bodies & beds; by sam theriac on Printables; fit: unverified; material: PLA (tested); hardware: Body clips
- [SCX24 Gladiator / Power Wagon Suspension Links](https://www.thingiverse.com/thing:7088464): Links; by Several_Split_4321 on Thingiverse; fit: unverified
- [SCX24 Magnetic Body Mounts](https://cults3d.com/en/3d-model/game/axial-scx24-magnetic-body-mounts): Body mounts; by HancockPrints on Cults3D; fit: unverified; material: PETG (designer); hardware: 20x2 mm magnets; hot glue
- [SCX24 LCG Battery Tray](https://makerworld.com/en/models/1986860-scx24-lcg-battery-tray): Battery trays; by Pylon_Musk on MakerWorld; fit: unverified; material: PETG
- [SCX24 Wide Beadlock Wheels](https://www.printables.com/model/191078-scx24-wide-beadlock-wheels): Wheels; by Forker45 on Printables; fit: unverified; material: PETG (designer); hardware: 16x M2x4 cap screws
- [SCX24 Low CG Battery Tray V1](https://makerworld.com/en/models/224882-scx24-low-cg-battery-tray-v1): Battery trays; by Yeti Engineering on MakerWorld; fit: unverified; material: PLA (print profile); hardware: Self-tapped with the included screws; 1 mm drill may be needed

## Traxxas TRX-4M (13 parts): https://crawlworx.com/chassis/trx-4m/

- [Bumper Shackle](https://www.printables.com/model/527012-bumper-shackle-for-traxxas-trx-4m-trx4m): Scale accessories; by Joza on Printables; fit: unverified; material: Resin (designer); hardware: 1 mm pin (a paper clip works)
- [ESC / Battery Upgrade](https://www.printables.com/model/336931-esc-battery-upgrade-for-trx4m): Battery trays; by Johnny_Tsunami on Printables; fit: reported; hardware: No extra hardware; uses the stock rubber strap
- [Front Bumper Mount for Injora LCG Chassis](https://www.printables.com/model/758643-trx4m-front-bumper-mount-for-injora-lcg-chassis): Bumpers; by Ratchet Finesse on Printables; fit: unverified
- [High Trail F-150 Front Tube Bumper](https://makerworld.com/en/models/741654-trx4m-hightrail-f150-front-tube-bumper): Bumpers; by ScaleRCdesigns on MakerWorld; fit: reported; material: PLA (print profile)
- [LCG Chassis Kit 1/18](https://makerworld.com/en/models/2091021-chasis-lcg-crawler-escala-1-18-kit): Chassis; by jonimi16 on MakerWorld; fit: unverified
- [Rock Sliders, Tube Style (F-150 & K10 High Trail)](https://cults3d.com/en/3d-model/game/trx4m-strong-bumper-with-hooks-fits-f-150-k10-high-trail): Sliders; by Hollow3D on Cults3D; fit: unverified; material: PLA or PETG; hardware: Factory hardware and holes
- [LCG Chassis Kit for TRX4m](https://cults3d.com/en/3d-model/game/lcg-chassis-kit-for-trx4m): Chassis; by m6light on Cults3D; fit: reported; material: PLA+ at 100% infill
- [Roofrack TRX4M Bronco](https://www.thingiverse.com/thing:5850755): Scale accessories; by navyblueboss on Thingiverse; fit: unverified; hardware: Small zip ties
- [TRX4M Bronco Roof Rack](https://www.printables.com/model/839258-trx4m-bronco-roof-rack): Scale accessories; by GaPa on Printables; fit: unverified; material: PLA (designer)
- [TRX4M Bronco Upgrade](https://www.printables.com/model/785156-trx4m-bronco-upgrade): Chassis; by GaPa on Printables; fit: unverified; hardware: 18650 cells, ESP32-C3 light box (optional)
- [TRX4M Chassis Upgrade](https://www.thingiverse.com/thing:5723777): Chassis; by Kubiczech81 on Thingiverse; fit: unverified; hardware: 8x M2x8 mm, 4x M2.5x14 mm
- [TRX4M Low Profile Bumpers / Hinged Body](https://www.printables.com/model/833241-trx4m-low-profile-bumpers-bumper-delete-and-hinged): Bumpers; by oclastax on Printables; fit: reported; material: PLA+ (designer); PETG or ABS fine; hardware: Don't overtighten the 2 center-bracket screws
- [TRX4M Rock Sliders](https://www.printables.com/model/655475-trx4m-rock-sliders): Sliders; by Ex-Pigeons on Printables; fit: unverified; hardware: M2x8 mm socket screws in place of the stock M2x6