Home / Axial SCX10 III

Axial · 1/10

Axial SCX10 III printable upgrades

The 1/10 trail benchmark: portal-ready axles, a DIG/2-speed LCX transmission, and a lot of body variants (Base Camp, JLU, Gladiator, Bronco). Check body compatibility before you print.

This page covers SCX10 III parts. SCX10 / SCX10 II parts usually do not fit.

14 parts · 4 reported · 10 unverified · none test-fitted by CrawlWorx yet · Gearing for the Axial SCX10 III →

Parts list

Unverified

SCX10 III Battery Box

by bwinkl04 on Thingiverse · Battery trays

Material: Not stated by source
Hardware: Not stated by source

The listing has no print or hardware notes.

View on Thingiverse (opens the original listing for SCX10 III Battery Box)

Reported fit

SCX10 III Gladiator Flatbed

by ahead_RC on Cults3D · Bodies & beds

Material: PLA+
Hardware: M3 countersunk 20 mm (5), 15 mm (4), 10 mm (7); M3 socket 10 mm (6) and 15-20 mm (4); 4 M3 nylocks; 4 M3 washers

Free. Built for ahead_RC's Gladiator overland build.

View on Cults3D (opens the original listing for SCX10 III Gladiator Flatbed)

Reported fit

Hinged Body Mount (Early Bronco)

by Zanthrax on Printables · Body mounts

Material: Not stated by source
Hardware: Stock screws; 50 mm M3 threaded rod (or 2x 25 mm screws) as hinge pin

Early Bronco body. Uses the stock mounting points. Designer runs it on their own truck.

View on Printables (opens the original listing for Hinged Body Mount (Early Bronco))

Unverified

SCX10 III Clipless Body Mount (JLU)

by NorfDesigns on Cults3D · Body mounts

Material: PLA+ or PETG
Hardware: Screws 3-5 mm longer than stock

For the JLU Wrangler body. Paid file.

View on Cults3D (opens the original listing for SCX10 III Clipless Body Mount (JLU))

Unverified

SCX10 III High Clearance Bumper

by Jimjo on Printables · Bumpers

Material: Nylon, ABS or PETG
Hardware: Heat-set version: 4x M3x4x5 mm inserts; reuses stock bumper screws

Designer: fits Basecamp; NOT compatible with JLU or other clipless-mount bodies.

View on Printables (opens the original listing for SCX10 III High Clearance Bumper)

Unverified

SCX10 III DIG Lever (1:1 replacement)

by Charly_Brown on Printables · Drivetrain

Material: PA6-CF (designer); PETG suggested
Hardware: 4x15 mm dowel pin

1:1 replacement for the lever in AXI232036. Description is in German.

View on Printables (opens the original listing for SCX10 III DIG Lever (1:1 replacement))

Unverified

SCX10 III Drive Shaft Improvement

by DustinTRC on Printables · Drivetrain

Material: PCTG, PETG, Nylon or ASA
Hardware: Not stated by source

Improves on the AXI232017 Wild Boar shafts. You can change the length in the slicer for other wheelbases. Thin sections may need clean-up.

View on Printables (opens the original listing for SCX10 III Drive Shaft Improvement)

Unverified

SCX10 III ESC Mount (Mamba X)

by Heliguy71 on Printables · Electronics mounts

Material: PETG
Hardware: 2x M3x6 mm screws; uses stock holes

Mounts a Mamba X ESC above the micro servo.

View on Printables (opens the original listing for SCX10 III ESC Mount (Mamba X))

Unverified

SCX10 III Front ESC Mount Plate

by irlbabayaga on MakerWorld · Electronics mounts

Material: ABS (print profile)
Hardware: Countersunk M3 screws

View on MakerWorld (opens the original listing for SCX10 III Front ESC Mount Plate)

Unverified

SCX10 III Gladiator Rails

by K&S Outdoors on MakerWorld · Scale accessories

Material: PLA (print profile)
Hardware: Not stated by source

Bed rails for the Gladiator body.

View on MakerWorld (opens the original listing for SCX10 III Gladiator Rails)

Unverified

SCX10 III Slick Slider

by Jimjo on Printables · Sliders

Material: Nylon, ABS or PETG
Hardware: 4x M3 countersunk screws, 8-10 mm

Bolts over the stock rock sliders. Designer says it fits all SCX10 III versions.

View on Printables (opens the original listing for SCX10 III Slick Slider)

Unverified

SCX10.3 Comp Sliders

by hodgecattleco on MakerWorld · Sliders

Material: PLA (print profile)
Hardware: Not stated by source

High-clearance sliders for any crawler with 30 mm skid bolt spacing.

View on MakerWorld (opens the original listing for SCX10.3 Comp Sliders)

Reported fit

SCX10 III Cantilever Suspension

by hotrodtrevor on Cults3D · Suspension

Material: 100% infill (material not stated)
Hardware: Spare screws plus 1 turnbuckle

Rear cantilever around the factory shock. Designer reports about 25 h of driving with one failure. Paid file.

View on Cults3D (opens the original listing for SCX10 III Cantilever Suspension)

Reported fit

SCX10 III Front Shock Towers (Base Camp)

by SB Artisan Creations on MakerWorld · Suspension

Material: PETG (tested); ABS-GF or PETG-CF suggested
Hardware: Not stated by source

Designer: direct replacement for the stock towers, no servo relocation needed. The listing has 17 reviews.

View on MakerWorld (opens the original listing for SCX10 III Front Shock Towers (Base Camp))

Links checked on 16 Oct 2026. Designers own their files; check the listing for license terms. Know a part that fits? Fit reports are coming with the newsletter.